2016 December Cisco Official New Released 200-401 Dumps in Lead2pass.com!
100% Free Download! 100% Pass Guaranteed!
After purchasing the dumps for the 200-401 Exam from Lead2pass, I had no doubt that I’d easily pass the exam. Bundle of thanks to Lead2pass for helping me pass the exam without any troubles.
Following questions and answers are all new published by Cisco Official Exam Center: http://www.lead2pass.com/200-401.html
Drag and Drop Question
According to the Purdue Reference Model, at which layer would you perform manufacturing operations and control?
A. Level 0
B. Level 1
C. Level 2
D. Level 3
E. Level 4
Refer to the exhibit. CCNA.com has the industrial network shown in the exhibit. All switches are configured as layer 2 switches and are using VLAN 1 as their management VLAN. Each VLAN 1 interface has been assigned the correct IP address. What is the purpose of assigning a default gateway to SW-C switch?
A. allows connectivity between the VLAN 1 interface on SW-C and other devices in the network.
B. allows connectivity between Host A and other devices in the network.
C. allows connectivity between Host B and other devices in the network.
D. allows the switch to pass traffic between Host A and Host B
What should be done with unused conductors in copper unshielded or shielded twisted-pair network cables?
A. terminate in their characteristic impedance
B. trim back and properly insulate
C. connect to protective earth
D. splice to a used conductor
Which option best describes a mechanical, ingress, climatic, chemical and electromagnetic environment that is classified as M3 I3 C3 E3?
A. the highest quality
B. office environment
D. serviced by multiple cable segments
With what are APC connectors used?
A. Category 6a cables that need tight radius bends
B. copper network cables in corrosive environments
C. single-mode fiber-optic cables to reduce return loss
D. high-density copper patch panels
Which characteristic causes multimode fiber-optic cable to differ from single mode?
A. by allowing multiple network services in the same cable
B. shorter maximum network segment length for a given bandwidth
C. a wider variety of available connector types
D. use outdoors as well as indoors
For which three issues should fiber-optic network segments be tested? (Choose three.)
B. near-end crosstalk
F. tensile stress
An Ethernet cable is attached to a PC NIC and then attached to a switch port. The PC power is turned on and the switch port link LED turns green. The link light indicates what two conditions? (Choose two.)
A. Layer 2 communication has been established between the PC and switch.
B. The PC has received a DHCP address.
C. Traffic is being sent from the switch to the PC.
D. If flashing, the green LED indicates port speed of 100 Mb/s.
E. The Layer 1 media is functioning between the PC and switch.
F. The switch port is functioning as a half-duplex connection.
At which Layer would you check ACLs for TCP ports being blocked?
A. Layer 1
B. Layer 2
C. Layer 3
D. Layer 4
I understood all of the questions very easily. I scored 96% on my first try. I am definitely going to spread the word amongst friends and colleagues. Keep up the great work.
200-401 new questions on Google Drive: https://drive.google.com/open?id=0B3Syig5i8gpDUjMxZHpSYkRSMmM
2016 Cisco 200-401 exam dumps (All 70 Q&As) from Lead2pass:
http://www.lead2pass.com/200-401.html [100% Exam Pass Guaranteed]
Why Choose Lead2pass?
If you want to pass the exam successfully in first attempt you have to choose the best IT study material provider, in my opinion, Lead2pass is one of the best way to prepare for the exam.
|One Time Purchase||✔||✖||✖||✖||✖|
|100% Pass Guarantee||✔||✖||✖||✖||✖|
|100% Money Back||✔||✖||✖||✖||✖|